NovaStar A10s Pro
An Armor receiving card for LED cabinets, with precise colour control, NCP configuration and redundancy.
- Mode-dependent loading
- 512 × 512 @ 60 Hz / 512 × 384 @ 60 Hz
- Parallel RGB data groups
- 32 groups
Purpose and capabilities
NovaStar A10s Pro is a compact Armor receiving card for professional LED displays. It receives the stream from a sending device and drives modules through a hub board. Its strengths are image-quality and service tools: Image Booster 3.0, HDR, frame-rate adaptation, calibration and NCP cabinet configuration. Available functions depend on the controller, driver ICs, firmware and actual screen configuration.
- 01Up to 512 × 512 pixels per card at 60 Hz with PWM drivers in an eligible 8-bit mode; 10- and 12-bit scenarios have separate limits.
- 0232 parallel RGB groups or 64 serial groups; the expanded 128-group mode uses pin multiplexing.
- 03Card, link, firmware and calibration redundancy support maintainable installations.
Image control for demanding scenes
Specification V1.5.1 lists HDR10 and HLG, colour-gamut management, fine low-grey control and frame-rate adaptation. These matter in dark scenes, camera work and mixed module batches. Actual results depend on the supported driver IC and configured signal path.
- Image Booster 3.0: colour management, fine grayscale and 22bit+; functions depend on the driver IC.
- Frame Rate Adaptive 3.0: a published 23–240 Hz range with a supported driver IC.
- Image rotation at 0°, 90°, 180° and 270°; arbitrary-angle rotation is not listed in the current specification.
Cabinet configuration with NCP
NCP binds firmware, configuration and image parameters to a specific cabinet. NovaStar describes NCP as the standard configuration path for new A10s Pro cabinets; the cabinet maker must provide a file matching the actual modules. COEX uses VMP, while certain MCTRL/H/VX workflows use NovaLCT 5.5.0 or later.
What an accurate selection needs
Before ordering, confirm cabinet wiring, module resolution and scan mode, driver IC, hub pinout, sending device, input bit depth and target frame rate. For an existing installation, also match the card revision, firmware and NCP file. A matching connector alone does not establish compatibility.
Where it is used
Receives controller data and drives LED modules. Selection requires the actual module driver, scan mode and pinout.
Signal path
- 01Sending device
- 02receiving card
- 03interface board/HUB
- 04LED modules
Check before selecting
Verify the exact hardware revision, firmware and complete signal chain. Maximum specifications do not guarantee simultaneous operation of all features. Catalogue inclusion does not confirm stock or rental availability.
Technical specifications
Values include conditions and sources where available. Configured systems may differ from the base model.
Capacity modes
Depends on controller mode, driver IC and firmware; verify for the actual display.
Model specification · V1.5.1Depends on controller mode, driver IC and firmware; verify for the actual display.
Model specification · V1.5.1Depends on controller mode, driver IC and firmware; verify for the actual display.
Model specification · V1.5.1Capacity and module interface
| Parameter | Value |
|---|---|
| Mode-dependent loading | 512 × 512 @ 60 Hz / 512 × 384 @ 60 Hz8 bit with PWM driver supports 512 × 512; 10 bit with COEX supports 512 × 512; 12 bit with another controller supports 512 × 384. Verify driver and firmware separately.Source · V1.5.1 · 简介 / 特性 / 接口 — Introduction / Features / Interfaces |
| Parallel RGB data groups | 32 groupsSource · V1.5.1 · 简介 / Introduction |
Electrical
| Parameter | Value |
|---|---|
| Rated power |
Mechanical and environment
| Parameter | Value |
|---|---|
| Dimensions | 80.0mm×45.0mm×8.2mmSource · V1.5.1 · 规格参数 / Specifications |
Model reviews
Reviews relate to the model. Used equipment condition and contents must be checked separately.
Loading reviews…
Compatibility and system composition
Device relationships depend on variant, revision, firmware and operating mode.
A matching brand or connector does not prove compatibility. Electrical and logical requirements and the complete signal chain must be checked.
Engineering status
Engineering review pending; full chain unapproved
NovaStar VX600 Pro
Ethernet sending is present; receiver firmware, cabinet file and port layout remain unverified. · V1.2.0
EvidenceNovaStar MCTRL660 PRO
Sending mode is documented; receiver firmware and port layout remain unverified. · V1.4.0
EvidenceNovaStar VX1000 Pro
Same ecosystem; exact pairing, firmware and mode are still unconfirmed. · document version not recorded
EvidenceExact-specification examples
Preliminary selection; not an installation drawing
NovaStar VX600 Pro
Sender: V1.4.0; receiver: V1.5.1. Mode, firmware, cabinet file, pinout and port routing are unapproved.
View modelAlternatives
For comparison, not a direct replacement without verification.
NovaStar A10s Plus-N
Compare specifications; not a verified replacement.
NovaStar A7s Plus
Compare specifications; not a verified replacement.
NovaStar A8s-N
Compare specifications; not a verified replacement.
NovaStar A8s Pro
Compare specifications; not a verified replacement.
Before confirming a project
- No approved pairing with a specific TOUCHLED LED module.
- Actual configuration, revision and firmware must be confirmed before supply.
Documents and software
Match software and firmware to the exact hardware and revision. Check the official source before installation.
Documentation
6Specification · V1.5.1 · Chinese
ZH · V1.5.1 · 1,452 KB · 2026-01-19
Current Chinese edition. Local copy of the official PDF for reliable access; the source is listed below.
Official software and firmware centre
This is the manufacturer's download centre, not a package selected for this SKU. Confirm version against hardware revision and the complete system before installing.
A10s Pro specification · V1.3.0 · EN (older edition)
EN · V1.3.0
For English reading. Check capacity limits and dimensions against the current Chinese V1.5.1 edition.
VMP user manual · V1.5.0 · EN
EN · V1.5.0
COEX system manual; feature availability depends on firmware and configuration.
NCP: cabinet library and file sourcing
EN
Official guide. Ask the cabinet manufacturer for the NCP file matching your cabinet.
NovaLCT synchronous system manual · V5.7.1 · Chinese
ZH · V5.7.1
Section 5.2.2.2 covers A10s Pro configuration through NCP.
